Amiga Modern Storage Guide

Gotek Floppy Emulator (FlashFloppy, OLED, DF0/DF1 jumpering), internal 44-pin IDE-to-SD/CF/mSATA adapters, and PCMCIA CF transfer kits.

1. Gotek Floppy Emulator & FlashFloppy Firmware

STM32F105 / Artery AT32F415 Gotek units running Keir Fraser's open-source FlashFloppy firmware.

DF0 / DF1 Jumpering & Boot Selector

  • Internal DF0: Replacement: Fit a single jumper on S0 (Drive Select 0, Shugart pin 10). Remove the factory S1 jumper used by IBM PCs! Leave MO open.
  • External DB23 Drive (DF1:): When connected via an external DB23-to-IDC34 adapter, set the Gotek jumper to S1 (or follow your adapter's DS line mapping).
  • DF0/DF1 Boot Selector Switch (A500/A2000): A socket interposer under Even CIA (CIA-A / U8) swaps pins 13 (/SEL0) and 14 (/SEL1), letting an external Gotek boot as DF0: while keeping the original internal 3.5″ drive uncut.

FlashFloppy FF.CFG, OLED & Rotary Mods

  • Essential FF.CFG Settings: Place FF.CFG in a FF/ folder or USB root with interface = shugart, host = amiga, nav-mode = native (or indexed), and chgrst = delay-3.
  • I2C OLED Display (0.91″ 128×32 or 0.96″ 128×64): Wire the 4-pin header (VCC=+3.3V/+5V, GND, SCL, SDA) to display full scrolling .ADF / .HFE filenames and track/head numbers.
  • Rotary Encoder (EC11) + Piezo Speaker: Wire encoder CLK/DT to the Gotek up/down button headers and SW to Pin 6 (Select/Eject) for rapid directory browsing; add a piezo buzzer on the speaker header for authentic track-step clicks.

2. Internal 44-Pin IDE-to-SD, CompactFlash & mSATA

Gayle 2.5″ IDE header wiring, the critical MaxTransfer = 0x1FE00 rule, and PFS3-AIO vs FFS filesystems.

44-Pin IDE Header & Adapter Selection

  • Pin 1 Orientation & +5V Power: The A600 and A1200 use a 2.0 mm pitch 44-pin IDE header driven by Gayle ($DA0000). Pins 41 & 42 carry +5 V (Logic & Motor) and Pin 43 is GND — plugging a 44-pin ribbon backwards shorts +5 V into ground/data pins and burns the trace!
  • IDE-to-SD (FC1307A bridge) vs Passive CF: Modern 44-pin SD2IDE adapters (FC1307A chip) have lower latency and seamless activity-LED support compared to picky CompactFlash cards; mSATA-to-44-pin enclosures offer highest write endurance.
  • A1200 Gayle Timing Capacitors: If fast CF/SD cards fail with read/write checksum errors on an A1200, remove EMI filter caps E123C & E125C near the IDE signals (and add the 470 Ω DRA0 pull-up on -02 Budgie boards).

The MaxTransfer = 0x1FE00 Rule & PFS3-AIO

  • Why Files Corrupt Without 0x1FE00: Kickstart's scsi.device issues single ATA sector count transfers up to 256 sectors (128 KB), which many CF/SD controllers misinterpret as 0 sectors, silently corrupting files >128 KB (especially WHDLoad archives).
  • Setting it in HDToolBox: Open Partition Drive → Advanced Options → Change, set MaxTransfer = 0x1FE00 (130,560 bytes) and Mask = 0x7FFFFFFE, and press Enter/Return inside the text box before clicking OK!
  • PFS3-AIO vs FastFileSystem (FFS): Standard Kickstart 3.0/3.1 FFS + scsi.device wraps around at the 4 GB (32-bit byte offset) boundary, destroying your boot partition. Use PFS3-AIO (Professional File System 3 All-In-One) or upgrade to Kickstart 3.1.4 / 3.2+ for safe >4 GB drives and instant boot validation.

3. PCMCIA CompactFlash Transfer Kits (A600 / A1200)

Sneakernet file transfers between Windows/macOS/Linux and your Amiga via FAT32 CF cards.

Software Stack: compactflash.device + FAT95

  1. Hardware: A passive 16-bit PCMCIA Type II to CompactFlash adapter + a 512 MB–4 GB CF card (SanDisk Ultra/Industrial recommended) formatted as FAT16 or FAT32 (MBR) on your PC.
  2. Driver Files: Copy compactflash.device → DEVS:, fat95 → L:, and the CF0 + CF0.info mountlist → DEVS:DOSDrivers/ (or SYS:Storage/DOSDrivers/ for on-demand mounting).
  3. Key CF0 Mountlist Parameters: Device = compactflash.device, FileSystem = L:fat95, Flags = 0 (or Flags = 2 for quirky CF cards), LowCyl = 0.

PCMCIA Troubleshooting & Reset Fix

  • 4 MB Zorro II RAM Conflict: The PCMCIA credit-card memory slot shares the $600000–$9FFFFF address range. Any A600 or A1200 24-bit Fast RAM expansion configured for 8 MB disables PCMCIA unless switched to 4 MB mode.
  • Kickstart 3.0/3.1 PCMCIA Reset Bug: Gayle does not assert CC_RESET (Pin 5) on cold boot. Either insert the PCMCIA adapter after Workbench loads, install the software tools CardPatch + CardReset in S:Startup-Sequence, or upgrade to Kickstart 3.1.4 / 3.2 (which fixes the reset in ROM).

Theme Palette

Default Dark
High-contrast dark
Amber Terminal
Monochrome amber
Matrix CRT
Phosphor green
Workbench Light
Clean light mode

Audio & Display

Relay Click Sounds Web Audio API — soft mechanical clicks
CRT Scanline & Flicker Pure CSS overlay effect

System Info

Customization Panel Theme preference, audio FX, and CRT overlay settings are saved to your browser's localStorage and persist between visits. No cookies or server-side storage is used.
Keyboard Shortcuts Press Esc to close this panel. Use the header moon/sun icon to cycle themes.