Amiga 600 & 1200 Bench Guide
SMD electrolytic replacement targets, leak repair, IDE header diagnostics and PCMCIA ESD protection for the compact Amigas.
SMD Capacitor Replacement Targets
Both machines use leak-prone SMD electrolytics — replace polymer-first and repair the damage underneath.
Amiga 600 (Rev 1.1 – 2B "June Bug")
- Audio: C401/C402 100 µF 6.3V, C403/C404 22 µF 16V, C405 10 µF — electrolyte crawls toward Paula and the LF347 op-amp.
- Power: C811–C813 47–100 µF near the fuse; C821/C822 on ±12 V rails (missing −12 V kills audio bias).
- Check vias between Gayle (U6) and the IDE header — corrosion here causes the classic "IDE not detected" fault.
Amiga 1200 (Rev 1A – 2B)
- Same C401–C405 + C811–C822 group; add C409 (10 µF floppy area) and, on Rev 1A, C819 near the IDE buffer.
- Leak damage around Lisa (U4) and Alice (U2) corrodes the fine RGA and DRA traces — inspect before blaming the AGA chips.
- Replace with polymer aluminium SMD (same footprint) or quality tantalum — tantalum polarity is REVERSED (stripe = positive).
Full capacitor tables for each board live on the Amiga Hub model selector.
Leak-repair rule: recap is only half the job. After removing each SMD cap, neutralise residue with vinegar, rinse with IPA, and continuity-test every via the electrolyte touched — "dead IDE" and "dead PCMCIA" on unrecapped boards are almost always corroded traces, not dead chips.
44-Pin IDE Header Diagnostics
Gayle drives the 2.5″ IDE port — most "no drive found" faults are open chip-select or strobe lines.
Pin-Level Checks (Gayle → Header)
- /IDE_CS1, /IDE_CS2 (Gayle pins 13–14 → header pins 37/38): both must pulse when the Kickstart probes $DA0000.
- /IORD, /IOWR (pins 19/18 → header 25/23) and /IDE_IRQ (pin 12 ← header 31).
- Check +5 V on header pins 41/42 and the buffer ICs between Gayle and the connector.
- White-screen hang on boot with a card fitted = drive never answering — check cable orientation (pin 1 marks) and adapter true-IDE mode.
The Famous A1200 IDE Fix
- -01 Budgie (391425-01): remove EMI capacitors E123C and E125C beside the IDE header — they round the /DSACK edges and corrupt reads on faster CF/SD cards.
- -02 Budgie (391425-02): also remove E123C/E125C and fit a 470 Ω pull-up on DRA0 (Alice pin 43).
- Symptoms without the fix: garbled filesystem, "not a DOS disk", freezes during large copies on CF/SD but a real 2.5″ HDD works.
PCMCIA Slot & ESD Protection
Gayle runs the 68-pin slot directly — ESD from cards is the usual killer.
Slot Diagnostics
- Card detect: /CC_CD1 & /CC_CD2 (Gayle pins 75/76) must both pull low when a card seats — corroded slot ground fingers are common.
- /CC_RESET (pin 5) should release high after boot; /REG (pin 7) strobes attribute/I-O space ($900000).
- SRAM/CF-PCMCIA adapters draw on the card edge — check for cracked slot solder joints on both rows.
ESD Precautions
- Never hot-swap PCMCIA cards — ground yourself first; a single zap takes out Gayle's card-detect or strobe pins.
- Prefer modern CF-to-PCMCIA adapters with proper 3.3 V translation; cheap passive ones stress the slot and Gayle outputs.
- Add a grounded metal shield/ejector plate if your machine travels — the slot is an open ESD doorway.
Gayle pinout for every check above: AA-Gayle interactive pinout.
Expansion Map & Trapdoor
- A600 PCMCIA (68-pin): Type II slot via Gayle; CF adapters, SRAM, network cards — 4 MB window.
- A1200 150-pin trapdoor: 68EC020 CPU slot for Blizzard/ACA accelerators + Fast RAM.
- A1200 clock port (Rev 2B): 22-pin $D80001 header — RTC plus third-party USB/Ethernet/MIDI boards.
- A600 CPU header: 80-pin edge for ACA620 or PiStorm adapters.