Amiga 500 & 500+ Bench Guide

Board revisions, Varta battery corrosion cleanup, 8372A Fat Agnus Chip-RAM mods, and 8520 CIA fault-finding for the best-selling Amiga.

Board Revisions & Identification

Match your ASSY number before ordering parts — clock chip, Agnus variant and Varta presence all change by revision.

RevASSYYearsAgnusChip RAMNotes
Rev 33104171987–888371 Fat Agnus (DIP-era board)512 KBEarly board; 8371 Agnus supports 512 KB only, 1 MB max with mods.
Rev 5310508 / 3125101988–898371 / 8372A512 KBFatter Agnus on later Rev 5; trapdoor A501 adds 512 KB + RTC.
Rev 6A3125131990–918372A (1 MB)512 KB onboardJP2/JP7A mods enable full 1 MB Chip RAM; ECS Agnus.
Rev 8 / 8A (A500+)3130xx series1991–928375 (2 MB)1 MB onboardECS chipset, onboard Varta battery + RTC, KS 2.04 ROM socketed.

Varta Battery Corrosion — Cleanup & Replacement

The A501 trapdoor card and every A500+ motherboard carry a barrel-shaped Varta NiCd rechargeable cell that leaks alkali (not acid!) onto the board. Corrosion is conductive, eats traces and vias, and migrates under IC sockets — treat every unopened A500+/A501 as corroded until proven otherwise.

Cleanup Steps

  1. Remove the barrel cell by snipping its legs flush — do NOT lever it off, the pads are already weak.
  2. Neutralise the alkali with white vinegar (acetic acid), 30–60 s, then scrub with a fibreglass pen or soft toothbrush.
  3. Rinse with 99% IPA, dry fully, then inspect every via in the fallout zone under magnification for dark rings.
  4. Continuity-test each affected trace end-to-end; patch opens with thin enamelled wire or a Kynar bodge.
  5. On A501s also check the RP101–RP104 resistor packs and RAM address lines — these corrode silently and cause random Chip-RAM errors.

Replacement Options

  • CR2032 + diode mod: 1N4148 in series with a lithium coin cell holder — safest, non-rechargeable.
  • Supercap mod: small 0.1–0.22 F supercapacitor; keeps RTC for days without chemistry.
  • Modern NiMH barrel: like-for-like replacement but still a leak risk long-term.
  • On the A500+ desolder cleanly: the battery sits near the keyboard MCU and RP105 — protect those pads.

Rule of thumb: if the machine will be used, remove the Varta today. A working A500+ with a leaking cell will not stay working.

8372A Agnus Chip-RAM Mods (Rev 5 & 6A)

Getting a full 1 MB of Chip RAM on classic A500 boards.

Rev 6A — The JP2/JP7A Mod

  • Fit an 8372A Fat Agnus in the U2 socket (8371 owners: the 8372A is a drop-in).
  • JP2: link pads 2–3 (or 1–2 depending on silkscreen — it routes Agnus pin 35 = A19 into the Chip-RAM address map). Verify your board's legend.
  • JP7A: cut the link so the second 512 KB bank is decoded as Chip RAM (/RAS1) rather than slow-ranger expansion.
  • Move the A501's RAM onto the motherboard map: with both banks Chip RAM you get the full 1 MB agnus-addressable space.
  • Pin 41 of the 8372A selects PAL/NTSC — strap low for PAL 50 Hz.

Rev 3 / Rev 5 — The 1 MB Agnus Swap

  • Swap 8371 → 8372A for the 1 MB map; wire A19 from Agnus pin 35 to the missing address line (the classic "A19 bodge wire" to the expansion edge).
  • Trapdoor 512 KB cards must be re-strapped or replaced with a 1 MB Chip-RAM adapter (Ranger→Chip remapper boards).
  • Verify with Avail or Workbench title — a working mod reports 1 MB Chip.
  • 8375 (A500+/A600 Agnus) is NOT pin-compatible — do not fit it in Rev 3/5/6A sockets.

Cross-check every strap against your ASSY number: Commodore moved JP2's meaning between revisions.

8520 CIA Testing (U7 & U8)

Both CIAs are socketed — isolate first, then prove with a swap.

Symptom → CIA Map

  • CIA-A (U7, even): dead keyboard, no power-LED blink, parallel port dead, /OVL overlay stuck (dark-grey screen), TOD clock stopped.
  • CIA-B (U8, odd): floppy never spins/seeks, serial port dead, audio filter stuck, mouse buttons/port 2 dead.
  • ESD from hot-plugging a joystick is the #1 CIA killer — single dead direction bits are typical.

Bench Isolation

  1. Confirm +5 V on pin 20, /RES released on pin 34, and the ~0.7 MHz E-clock on pin 25 of BOTH chips (E-clock comes from Gary — no clock = Gary fault).
  2. Check /CS on pin 23 strobes during a CIA access ($BFxxxx).
  3. Power off and swap U7 ↔ U8: if the fault moves (keyboard dead → floppy dead), the chip is bad.
  4. 8521 and good-condition 6526s are usable substitutes; verify keyboard + floppy after fitting.

Full pin map: 8520 CIA pinout · isolation flowchart: Amiga Diagnostics.

Theme Palette

Default Dark
High-contrast dark
Amber Terminal
Monochrome amber
Matrix CRT
Phosphor green
Workbench Light
Clean light mode

Audio & Display

Relay Click Sounds Web Audio API — soft mechanical clicks
CRT Scanline & Flicker Pure CSS overlay effect

System Info

Customization Panel Theme preference, audio FX, and CRT overlay settings are saved to your browser's localStorage and persist between visits. No cookies or server-side storage is used.
Keyboard Shortcuts Press Esc to close this panel. Use the header moon/sun icon to cycle themes.