Pinout diagram
Used in Retro Machine Hubs
Click any system badge below to jump directly to its dedicated repair, schematic, and diagnostic Machine Hub:
Summary specifications
Full pin reference
| Pin | Name | Group | Direction | Levels | Description | Expected Signal |
|---|---|---|---|---|---|---|
| 1 | GND | Ground | Power | 0 V | Ground. | |
| 2 | PA0 | I/O | Bidirectional | TTL | Port A bit 0 — CIA-A: parallel/keyboard; CIA-B: serial/floppy select line. | |
| 3 | PA1 | I/O | Bidirectional | TTL | Port A bit 1. | |
| 4 | PA2 | I/O | Bidirectional | TTL | Port A bit 2. | |
| 5 | PA3 | I/O | Bidirectional | TTL | Port A bit 3. | |
| 6 | PA4 | I/O | Bidirectional | TTL | Port A bit 4. | |
| 7 | PA5 | I/O | Bidirectional | TTL | Port A bit 5. | |
| 8 | PA6 | I/O | Bidirectional | TTL | Port A bit 6. | |
| 9 | PA7 | I/O | Bidirectional | TTL | Port A bit 7. | |
| 10 | PB0 | I/O | Bidirectional | TTL | Port B bit 0 — CIA-A: /OVL overlay control; CIA-B: drive /STEP. | |
| 11 | PB1 | I/O | Bidirectional | TTL | Port B bit 1 — CIA-B: /DIR step direction. | |
| 12 | PB2 | I/O | Bidirectional | TTL | Port B bit 2 — CIA-B: /SIDE head select. | |
| 13 | PB3 | I/O | Bidirectional | TTL | Port B bit 3 — CIA-B: /SEL3 drive select. | |
| 14 | PB4 | I/O | Bidirectional | TTL | Port B bit 4 — CIA-B: /SEL2 drive select. | |
| 15 | PB5 | I/O | Bidirectional | TTL | Port B bit 5 — CIA-B: /SEL1 drive select. | |
| 16 | PB6 | I/O | Bidirectional | TTL | Port B bit 6 — CIA-B: /SEL0 (DF0) drive select. | |
| 17 | PB7 | I/O | Bidirectional | TTL | Port B bit 7 — CIA-B: /MTR motor-on latch. | |
| 18 | /PC | Control | Output | TTL, active low | Port C handshaking output — CIA-B drives the serial/latch line. | |
| 19 | TOD | Clock / Timing | Input | TTL 50/60 Hz | Time-of-day tick input — wired to /VSYNC on Amiga (NOT mains 50/60 Hz like the C64). | |
| 20 | VCC | Power | Power | +5 V | +5 V supply. | |
| 21 | /IRQ | Control | Open-drain / open-collector | TTL, active low, open-drain | Interrupt request — routed to Paula INT6 (CIA-A) / INT2 (CIA-B) level encoders. | |
| 22 | R/W | Control | Input | TTL | 68000 read/write via bus buffers. | |
| 23 | /CS | Control | Input | TTL, active low | Chip select — /EVEN_CIA or /ODD_CIA from Gary/Gayle. | |
| 24 | /FLAG | Control | Input | TTL, active low | FLAG input — CIA-B: /INDEX? Used for serial/flag handshakes. | |
| 25 | PHI2 (E) | Clock / Timing | Input | TTL ~0.7 MHz | E-clock input from Gary/Gayle — the 6800-cycle timing reference; CIA is dead without it. | |
| 26 | D7 | Data Bus | Bidirectional | TTL | Data bus bit 7 (MSB). | |
| 27 | D6 | Data Bus | Bidirectional | TTL | Data bus bit 6. | |
| 28 | D5 | Data Bus | Bidirectional | TTL | Data bus bit 5. | |
| 29 | D4 | Data Bus | Bidirectional | TTL | Data bus bit 4. | |
| 30 | D3 | Data Bus | Bidirectional | TTL | Data bus bit 3. | |
| 31 | D2 | Data Bus | Bidirectional | TTL | Data bus bit 2. | |
| 32 | D1 | Data Bus | Bidirectional | TTL | Data bus bit 1. | |
| 33 | D0 | Data Bus | Bidirectional | TTL | Data bus bit 0 (LSB). | |
| 34 | /RES | Control | Input | TTL, active low | Reset input — clears ports to input mode on power-up. | |
| 35 | RS3 | Address Bus | Input | TTL | Register select 3 (from A11). | |
| 36 | RS2 | Address Bus | Input | TTL | Register select 2 (from A10). | |
| 37 | RS1 | Address Bus | Input | TTL | Register select 1 (from A9). | |
| 38 | RS0 | Address Bus | Input | TTL | Register select 0 (from A8). | |
| 39 | SP | I/O | Bidirectional | TTL | Serial port shift register — CIA-A: keyboard data line. | |
| 40 | CNT | I/O | Bidirectional | TTL | Serial counter clock — CIA-A: keyboard clock line. |
Common uses and repair diagnostics
Every Amiga carries two MOS/CSG 8520 Complex Interface Adapters. CIA-A ('even', U7 on A500, U300 on some boards) owns the parallel port, keyboard serial interface, power LED, /OVL Kickstart-overlay bit and left mouse/joystick port. CIA-B ('odd', U8) owns floppy /SELx//MTR//STEP//DIR//SIDE, the serial port, right joystick port and the audio low-pass filter switch. The 8520 is electrically a 6526 variant — same DIP-40 pinout — but its TOD input is designed for a 50/60 Hz tick (wired to /VSYNC on the Amiga), and it is notoriously ESD-sensitive on the joystick ports.
Every Amiga model uses two 8520s. CIA-A (even, at $BFE001 register base) handles keyboard serial data on SP/CNT, the parallel port, power LED, and the /OVL line that maps Kickstart to $000000 after reset. CIA-B (odd, at $BFD000) handles floppy /SEL0-3, /MTR, /STEP, /DIR, /SIDE, the serial port, right-hand controller port and the audio filter relay.
Cross-reference: the C64's 6526 CIA is the same silicon family and pinout — the Amiga variant replaces the mains-frequency TOD with a /VSYNC-derived tick.
- Dead keyboard + no power-LED boot blink = CIA-A: verify E-clock at pin 25 (~0.7 MHz), /CS at pin 23, then swap U7 with a known-good 8520 (it is socketed on most boards).
- Floppy motor never spins / drive not selected = CIA-B port B (pins 10-17): check /SEL0-3 and /MTR lines to the DB23 floppy header for shorts to the +5V rail.
- Hot-plug damage: plugging a joystick in while powered latches the port pins — if one direction/button dies on a port, suspect the CIA, not the mouse.
- /IRQ pin 21 is open-drain — a failed pull-up or shorted CIA holds the line low and the machine Guru-meditates or hangs during Workbench IRQ storms.
- When swapping 6526 spares in from C64s: electrically compatible for most tests, but confirm the TOD tick source and serial register behaviour before calling it a permanent fix.