CSG 5719 Gary Pinout — Amiga 500/2000 Bus Controller, Address Decoder & DTACK Generator (DIP-48)

DIP-48 · Support & Peripheral · CSG 5719 (318072-01) / 5718 (DIP-48); Fat Gary 390540 (PLCC-84)

MOS/CSG 5719 Gary (Gate Array) (DIP-48) — Printable IC Pinout & Signal SheetHigh-contrast DIP/PLCC pinout diagram, supply pin highlights (+5V/GND/+12V), and full 48-pin table.

Pinout diagram

Used in Retro Machine Hubs

Click any system badge below to jump directly to its dedicated repair, schematic, and diagnostic Machine Hub:

Summary specifications

Technology Gate array (structured ASIC)
Operating Voltage +5 V +/-5% (VDD pins 6, 17, 48; VSS pins 1, 24)
Clock Inputs C1/C3 3.58 MHz quadrature + /CDAC 7.14 MHz from Agnus
Decodes /RAME, /ROME, /RGAE, /VPA, /RTCR, /RTCW, BANK0-BANK7 memory banks
Swap Note 5718 and 5719 are pin-compatible; always use the MOS/CSG-made part — early Toshiba 5718s in Rev 4.x A2000s have Zorro II timing bugs.
Max Current 25 mA

Full pin reference

Pin Name Group Direction Levels Description Expected Signal
1 VSS Ground Power 0 V Ground supply.
2 /VPA Control Output TTL, active low Valid Peripheral Address — tells the 68000 to run a slow 6800-style E cycle for the 8520 CIAs.
3 /CDR Control Output TTL, active low Enables video-bus read buffers to drive the CPU data bus.
4 /CDW Control Output TTL, active low Enables CPU data-bus buffers to drive the video (Chip RAM) data bus.
5 /KRES Control Input TTL, active low Power-up / keyboard reset input — drives /RESET + /HALT sequence.
6 VDD Power Power +5 V +5 V supply.
7 /MTR Control Input TTL, active low Disk motor enable input from Paula/CIA.
8 /DKWD Control Input TTL, active low Disk write data input from Paula.
9 DKWE Control Input TTL, active high Disk write enable input (write gate).
10 /LDS Control Input TTL, active low 68000 Lower Data Strobe (D0-D7 valid).
11 /UDS Control Input TTL, active low 68000 Upper Data Strobe (D8-D15 valid).
12 PRW Control Input TTL Processor Read/Write — bus direction.
13 /AS Control Input TTL, active low 68000 Address Strobe — qualifies all address decodes.
14 /BGACK Control Input TTL, active low Bus Grant Acknowledge — external DMA master owns the bus.
15 /DBR Control Input TTL, active low DMA Bus Request from Agnus — video-bus DMA in progress; delays /DTACK.
16 /SEL0 Control Input TTL, active low Drive select 0 input (floppy select qualification).
17 VDD Power Power +5 V +5 V supply.
18 /RGAE Control Output TTL, active low Register Enable — decodes $DFF000-$DFF1FF custom-chip register space to Agnus/Denise/Paula.
19 /BLS Control Output TTL, active low Blitter Slowdown — asserted to Agnus when CPU addresses BANK6 so blitter yields Chip RAM cycles.
20 /RAME Control Output TTL, active low Chip RAM (video bus RAM) address decode enable to Agnus.
21 /ROME Control Output TTL, active low Kickstart ROM chip select ($F80000 / $000000 overlay).
22 /RTCR Control Output TTL, active low Real-Time Clock read enable.
23 /RTCW Control Output TTL, active low Real-Time Clock write enable.
24 VSS Ground Power 0 V Ground supply.
25 C4 Clock / Timing Output TTL Clock 4 output — latches data on the video data bus.
26 /CDAC Clock / Timing Input TTL 7.14 MHz 7.14 MHz clock input from Agnus (CDAC).
27 C3 Clock / Timing Input TTL 3.58 MHz 3.58 MHz colour clock, 90-degree lag of C1.
28 C1 Clock / Timing Input TTL 3.58 MHz 3.58 MHz master colour clock input.
29 /OVR Control Input TTL, active low Override — tri-states Gary's /DTACK and internal device selects so expansion hardware can own the bus.
30 OVL Control Input TTL, active high Overlay input (from CIA-A PB) — maps Kickstart ROM to address $000000 after reset.
31 XRDY Control Input TTL, active high External Ready — expansion logic can delay internal /DTACK for wait states.
32 /EXP Control Input TTL, active low Expansion RAM present flag — pulled low by trapdoor/side expansion cards.
33 A17 Address Bus Input TTL 68000 address bit 17.
34 A18 Address Bus Input TTL 68000 address bit 18.
35 A19 Address Bus Input TTL 68000 address bit 19.
36 A20 Address Bus Input TTL 68000 address bit 20.
37 A21 Address Bus Input TTL 68000 address bit 21.
38 A22 Address Bus Input TTL 68000 address bit 22.
39 A23 Address Bus Input TTL 68000 address bit 23 (MSB of decode).
40 N/C No Connect Not connected - No connect.
41 /RESET Control Open-drain / open-collector TTL, active low, open-drain Open-drain 68000 /RESET output — released ~500 ms after power-up via /KRES.
42 /HALT Control Tri-state output TTL, active low 68000 /HALT output — held with /RESET during power-up; re-asserted on double bus fault.
43 /DTACK Control Open-drain / open-collector TTL, active low, open-drain Data Transfer Acknowledge — the single most important Gary output; the 68000 waits forever if it never goes low.
44 DKWEB Control Output TTL, active high Buffered disk write enable to the floppy header.
45 DKWDB Control Output TTL, active high Buffered disk write data to the floppy header.
46 MTR0D Control Output TTL, active high Latched drive-0 motor-on output.
47 MTRXD Control Output TTL, active high Buffered /MTR motor signal to all drives.
48 VDD Power Power +5 V +5 V supply.

Common uses and repair diagnostics

Gary ('GAte arraY', CSG 5719 in the A500/A500+/CDTV and 5718 in early A2000s, both under part 318072-01) consolidates the dozens of 74-series decoders and PALs used in the A1000 into a single 48-pin DIP. It decodes the 68000's A17-A23 into the /RAME (Chip RAM), /ROME (Kickstart ROM), /RGAE (custom-chip register) and /VPA (8520 CIA 6800-cycle) selects, generates /DTACK for every onboard access, drives the open-drain /RESET and /HALT lines, buffers the floppy write signals, and decides when the blitter may steal Chip RAM cycles (/BLS to Agnus). The A3000/A4000 use the PLCC-84 'Fat Gary' (390540) — a different package with wider buses.

Fitted in the Amiga 500 (U5), A500+, Amiga 2000-B and CDTV. Replaced by Gayle in the A600/A1200 and by Fat Gary + Super Buster in the A3000/A4000.

A black-screen Amiga that pulses /AS but never sees /DTACK return is the classic Gary-or-clocks fault: Gary cannot produce /DTACK without its C1, C3 and /CDAC clocks from Agnus, so verify those first. A dead /ROME decode gives a dark-grey screen; a stuck /VPA kills the CIA bus cycle and dead keyboard.

  • Probe Pin 43 (/DTACK): it must toggle low on every bus cycle. A CPU that pulses /AS with /DTACK held high points at Gary, a missing C1/C3/CDAC clock, or an expansion card holding /OVR low.
  • Pin 41 (/RESET) and Pin 42 (/HALT) are open-drain — check the pull-ups; a broken /HALT pull-up mimics a dead 68000.
  • On an A500, Gary (U5) sits in a 48-pin DIP socket. Extract evenly from both ends — the pins bend and tear socket contacts easily.
  • Green screen after a Gary swap: re-check pin 30 (OVL) — without the CIA-A overlay bit the Kickstart ROM never maps to $000000.
  • Early Toshiba-made 5718s in Rev 4.x A2000 boards have Zorro II timing bugs — replace with the MOS/CSG 5719.

Datasheets and references

Related chips

Theme Palette

Default Dark
High-contrast dark
Amber Terminal
Monochrome amber
Matrix CRT
Phosphor green
Workbench Light
Clean light mode

Audio & Display

Relay Click Sounds Web Audio API — soft mechanical clicks
CRT Scanline & Flicker Pure CSS overlay effect

System Info

Customization Panel Theme preference, audio FX, and CRT overlay settings are saved to your browser's localStorage and persist between visits. No cookies or server-side storage is used.
Keyboard Shortcuts Press Esc to close this panel. Use the header moon/sun icon to cycle themes.