Pinout diagram
Used in Retro Machine Hubs
Click any system badge below to jump directly to its dedicated repair, schematic, and diagnostic Machine Hub:
Summary specifications
Full pin reference
| Pin | Name | Group | Direction | Levels | Description | Expected Signal |
|---|---|---|---|---|---|---|
| 1 | PE12 | Control | Output | TTL | PCMCIA card edge signal PE12. | |
| 2 | PE5 | Control | Output | TTL | PCMCIA card edge signal PE5. | |
| 3 | GND1 | Ground | Power | 0 V | Ground. | |
| 4 | NOISE | Control | Output | TTL | Noise output via C711 (clock port noise line). | |
| 5 | CC_RESET | Control | Output | TTL | PCMCIA card reset output. | |
| 6 | /CC_ENA | Control | Output | TTL, active low | PCMCIA card enable strobe. | |
| 7 | /REG | Control | Output | TTL, active low | PCMCIA attribute/I-O register select (vs common memory). | |
| 8 | /WE | Control | Output | TTL, active low | PCMCIA write enable. | |
| 9 | /OE | Control | Output | TTL, active low | PCMCIA output enable (read strobe). | |
| 10 | E | Clock / Timing | Output | TTL ~0.7 MHz | 6800 E-clock output via E112 — clocks the 8520 CIAs. | |
| 11 | /FLASH | Control | Output | TTL, active low | Flash ROM chip select. | |
| 12 | /IDE_IRQ | Control | Input | TTL, active low | IDE interrupt request input from 44-pin header (INTRQ pin 31). | |
| 13 | /IDE_CS1 | Control | Output | TTL, active low | IDE command block chip select (header pin 37 /CS0). | |
| 14 | /IDE_CS2 | Control | Output | TTL, active low | IDE control block chip select (header pin 38 /CS1). | |
| 15 | /SPARE_CS | Control | Output | TTL, active low | Spare chip select. | |
| 16 | /NET_CS | Control | Output | TTL, active low | Network (ARCNET) chip select decode. | |
| 17 | /RTC_CS | Control | Output | TTL, active low | Real-time clock chip select. | |
| 18 | /IOWR | Control | Output | TTL, active low | IDE/PCMCIA write strobe (header pin 23 /DIOW). | |
| 19 | /IORD | Control | Output | TTL, active low | IDE/PCMCIA read strobe (header pin 25 /DIOR). | |
| 20 | VCC1 | Power | Power | +5 V | +5 V supply. | |
| 21 | /ROMEN | Control | Output | TTL, active low | Kickstart ROM enable via E113. | |
| 22 | C14M | Clock / Timing | Input | TTL 14 MHz | CPU clock input (CPUCLK). | |
| 23 | CCK | Clock / Timing | Input | TTL 3.55 MHz | Colour clock input. | |
| 24 | GND2 | Ground | Power | 0 V | Ground. | |
| 25 | XRDY | Control | Input | TTL | External ready — wait-state request input. | |
| 26 | /OVR | Control | Input | TTL, active low | Override — disables internal decodes/DSACK for expansion logic. | |
| 27 | CC_A0 | Address Bus | Output | TTL | PCMCIA card address bit 0. | |
| 28 | /OEB | Control | Output | TTL, active low | Output enable buffer via E114. | |
| 29 | /DBR | Control | Bidirectional | TTL, active low | DMA bus request line. | |
| 30 | /BLS | Control | Output | TTL, active low | Blitter slowdown via XU2/U26X. | |
| 31 | /REGEN | Control | Bidirectional | TTL, active low | Custom-chip register enable decode. | |
| 32 | /RAMEN | Control | Output | TTL, active low | Chip RAM enable via XU2/XU3. | |
| 33 | /AS | Control | Input | TTL, active low | Address strobe input via XU1. | |
| 34 | /DS | Control | Input | TTL, active low | Data strobe input (/UDS//LDS combined). | |
| 35 | /DSACK1 | Control | Bidirectional | TTL, active low | 68020 DSACK1 via R115 — with DSACK0 signals 16-bit port completion. | |
| 36 | R_W | Control | Input | TTL | 68020 read/write direction input. | |
| 37 | /DSACK0 | Control | Bidirectional | TTL, active low | 68020 DSACK0 via R113 — A1200 IDE timing mod removes delay caps here. | |
| 38 | /BG | Control | Input | TTL, active low | Bus grant input (/ZORRO on A1200 schematic). | |
| 39 | /HLT | Control | Input | TTL, active low | Halt input via R117. | |
| 40 | /RST | Control | Input | TTL, active low | System reset input via R116. | |
| 41 | A12 | Address Bus | Input | TTL | CPU address bit 12. | |
| 42 | A13 | Address Bus | Input | TTL | CPU address bit 13. | |
| 43 | A14 | Address Bus | Input | TTL | CPU address bit 14. | |
| 44 | A15 | Address Bus | Input | TTL | CPU address bit 15. | |
| 45 | GND3 | Ground | Power | 0 V | Ground. | |
| 46 | A16 | Address Bus | Input | TTL | CPU address bit 16. | |
| 47 | A17 | Address Bus | Input | TTL | CPU address bit 17. | |
| 48 | A18 | Address Bus | Input | TTL | CPU address bit 18. | |
| 49 | A19 | Address Bus | Input | TTL | CPU address bit 19. | |
| 50 | A20 | Address Bus | Input | TTL | CPU address bit 20. | |
| 51 | A21 | Address Bus | Input | TTL | CPU address bit 21. | |
| 52 | A22 | Address Bus | Input | TTL | CPU address bit 22. | |
| 53 | A23 | Address Bus | Input | TTL | CPU address bit 23. | |
| 54 | D31 | Data Bus | Bidirectional | TTL | 68020 data bit 31 (Gayle port D15 in spec). | |
| 55 | D30 | Data Bus | Bidirectional | TTL | 68020 data bit 30. | |
| 56 | D29 | Data Bus | Bidirectional | TTL | 68020 data bit 29. | |
| 57 | D28 | Data Bus | Bidirectional | TTL | 68020 data bit 28. | |
| 58 | D27 | Data Bus | Bidirectional | TTL | 68020 data bit 27. | |
| 59 | D26 | Data Bus | Bidirectional | TTL | 68020 data bit 26. | |
| 60 | D25 | Data Bus | Bidirectional | TTL | 68020 data bit 25. | |
| 61 | D24 | Data Bus | Bidirectional | TTL | 68020 data bit 24. | |
| 62 | VCC2 | Power | Power | +5 V | +5 V supply. | |
| 63 | /KBRESET | Control | Input | TTL, active low | Keyboard reset input from keyboard MCU. | |
| 64 | /SENSE | Control | Input | TTL, active low | Coprocessor presence sense (/FPU_MUSH on A1200 schematic). | |
| 65 | /FPU_CS | Control | Output | TTL, active low | FPU chip select decode. | |
| 66 | GND4 | Ground | Power | 0 V | Ground. | |
| 67 | /MTRON | Control | Output | TTL, active low | Floppy drive-0 motor-on latch (/MTR0). | |
| 68 | /WIDE | Control | Output | TTL, active low | Wide-data-path flag to chipset. | |
| 69 | FC1 | Control | Input | TTL | 68020 function code bit 1. | |
| 70 | FC0 | Control | Input | TTL | 68020 function code bit 0. | |
| 71 | /MTR | Control | Input | TTL, active low | Floppy motor-on input. | |
| 72 | /SEL | Control | Input | TTL, active low | Floppy drive select input (/SEL0). | |
| 73 | /ODD_CIA | Control | Output | TTL, active low | Odd 8520 CIA (CIA-B) chip select. | |
| 74 | /EVEN_CIA | Control | Output | TTL, active low | Even 8520 CIA (CIA-A) chip select. | |
| 75 | /CC_CD1 | Control | Input | TTL, active low | PCMCIA card detect 1. | |
| 76 | /CC_CD2 | Control | Input | TTL, active low | PCMCIA card detect 2. | |
| 77 | /CC_BVD1 | Control | Input | TTL, active low | PCMCIA battery voltage detect 1. | |
| 78 | /CC_BVD2 | Control | Input | TTL, active low | PCMCIA battery voltage detect 2. | |
| 79 | /CC_WP | Control | Input | TTL, active low | PCMCIA write-protect sense. | |
| 80 | /CC_BUSY | Control | Input | TTL, active low | PCMCIA busy/interrupt request (/CC_BUSY_IREQ). | |
| 81 | /WAIT | Control | Input | TTL, active low | PCMCIA wait-state input — extends DSACK timing. | |
| 82 | /BERR | Control | Bidirectional | TTL, active low | Bus error line via R114. | |
| 83 | /INT6 | Control | Output | TTL, active low | Interrupt level-6 request output. | |
| 84 | /INT2 | Control | Output | TTL, active low | Interrupt level-2 request output. |
Common uses and repair diagnostics
AA-Gayle (391424-02, U5 on the A1200; Gayle 391155, U6/U600 on the A600) is the 1990s replacement for Gary. It keeps the address decode, /DSACK and floppy duties and adds a buffered 44-pin IDE host interface, the 68-pin PCMCIA card controller, RTC chip-select, and the /EVEN_CIA//ODD_CIA strobes. The A600 variant and the AGA 'AA-Gayle' are not interchangeable. Gayle is soldered — SMD capacitor electrolyte corrodes the fine traces fanning out to the IDE header and PCMCIA slot, so 'dead IDE' and 'dead PCMCIA' faults on unrecapped boards are usually corrosion, not the chip.
A600 (Gayle 391155, U6) and A1200 (AA-Gayle 391424-02, U5). Every IDE and PCMCIA access flows through Gayle, so a corroded board kills storage first: the classic A1200 'no CF card detected' fault is usually electrolyte-open /IDE_CS or /IORD//IOWR traces, not the silicon.
- IDE dead on A600/A1200: continuity-check pins 13-14 (/IDE_CS), 18-19 (/IOWR//IORD) and 12 (/IDE_IRQ) to the 44-pin header — capacitor electrolyte eats these traces first.
- PCMCIA card not detected: verify pins 75-76 (/CC_CD1-2) pull low when a card seats; corroded vias at the slot are the usual culprit.
- A1200 IDE corruption: Rev 1D4/2B boards need the EMI-cap fix — remove E123C/E125C near the IDE header, and with -02 Budgie add a 470-ohm pull-up on DRA0.
- DSACK faults hang the 68020 mid-cycle: check pins 35/37 and the series resistors R113/R115 before condemning the chip.
- Gayle is soldered PLCC — always complete the SMD recap and trace repair before attempting rework; lifted J-lead pads are common.