Intel 8088 & NEC V20 CPU Pinout — 16-Bit x86 Processor with 8-Bit External Bus (DIP-40)

DIP-40 · CPUs & MPUs · Intel D8088 / P8088-2 / SAB8088-1-P / NEC uPD70108C (V20) — DIP-40

Intel 8088 / Siemens SAB8088 / NEC V20 CPU (DIP-40) — Printable IC Pinout & Signal SheetHigh-contrast DIP/PLCC pinout diagram, supply pin highlights (+5V/GND/+12V), and full 40-pin table.

Pinout diagram

Used in Retro Machine Hubs

Click any system badge below to jump directly to its dedicated repair, schematic, and diagnostic Machine Hub:

Summary specifications

Technology HMOS (8088) / CMOS (80C88, NEC V20)
Operating Voltage +5.0 V +/-5% (VCC Pin 40; GND Pins 1, 20)
Clock Frequency 4.77 MHz (PC-1/XT), 7.16 MHz & 9.54 MHz Turbo (PC-10-III/PC-20-III/Colt, 33% duty cycle)
Address / Data Bus 20-bit Address (1 MB, A0-A19), 8-bit Multiplexed Data (AD0-AD7)
NEC V20 Upgrade Drop-in DIP-40 replacement adding 80186 instructions and 15-25% higher throughput (enables XT-IDE ide_xtp.bin)

Full pin reference

Pin Name Group Direction Levels Description Expected Signal
1 GND Ground Power 0 V Ground (connect BOTH Pin 1 and Pin 20 to 0 V).
2 A14 Address Bus Output TTL Address bit 14.
3 A13 Address Bus Output TTL Address bit 13.
4 A12 Address Bus Output TTL Address bit 12.
5 A11 Address Bus Output TTL Address bit 11.
6 A10 Address Bus Output TTL Address bit 10.
7 A9 Address Bus Output TTL Address bit 9.
8 A8 Address Bus Output TTL Address bit 8.
9 AD7 Data Bus Bidirectional TTL Multiplexed Address bit 7 (T1) / Data bit 7 (T2-T4).
10 AD6 Data Bus Bidirectional TTL Multiplexed Address/Data bit 6.
11 AD5 Data Bus Bidirectional TTL Multiplexed Address/Data bit 5.
12 AD4 Data Bus Bidirectional TTL Multiplexed Address/Data bit 4.
13 AD3 Data Bus Bidirectional TTL Multiplexed Address/Data bit 3.
14 AD2 Data Bus Bidirectional TTL Multiplexed Address/Data bit 2.
15 AD1 Data Bus Bidirectional TTL Multiplexed Address/Data bit 1.
16 AD0 Data Bus Bidirectional TTL Multiplexed Address/Data bit 0 (LSB).
17 NMI Control Input TTL, rising-edge Non-Maskable Interrupt (RAM parity error / 8087 exception).
18 INTR Control Input TTL, active high Maskable Interrupt Request from 8259A PIC / FE2010A.
19 CLK Clock / Timing Input TTL 33% duty 33%-duty-cycle system clock from 8284A / FE2010A (4.77 / 7.16 / 9.54 MHz).
20 GND Ground Power 0 V Ground.
21 RESET Control Input TTL, active HIGH Active-HIGH Reset input — held HIGH while PSU Power Good is low; on release, CPU fetches FFFF:0000.
22 READY Control Input TTL, active high Bus Ready input — if held LOW by a hung ISA card or DMA controller, CPU inserts wait states forever.
23 /TEST Control Input TTL, active low Wait-for-Test input driven by 8087 FPU BUSY pin.
24 /QS1 (INTA) Control Output TTL Queue Status 1 (Max Mode) / /INTA (Min Mode).
25 /QS0 (ALE) Control Output TTL Queue Status 0 (Max Mode) / Address Latch Enable (Min Mode).
26 /S0 (DEN) Control Output TTL Bus Status 0 to 8288/FE2010A (Max Mode).
27 /S1 (DT/R) Control Output TTL Bus Status 1 to 8288/FE2010A (Max Mode).
28 /S2 (IO/M) Control Output TTL Bus Status 2 to 8288/FE2010A (Max Mode).
29 /LOCK (WR) Control Output TTL Bus Lock output (Max Mode) / /WR (Min Mode).
30 /RQ/GT1 Control Bidirectional TTL Request/Grant bus arbitration 1.
31 /RQ/GT0 Control Bidirectional TTL Request/Grant 0 (8087 / DMA bus request).
32 /RD Control Output TTL, active low Read strobe output.
33 MN//MX Control Input TTL strap Minimum/Maximum mode strap — tied to GND (Max Mode) in PC/XT and Commodore PC systems.
34 /SS0 (HIGH) Control Output TTL Status line SS0.
35 A19/S6 Address Bus Output TTL Multiplexed Address bit 19 (MSB of 1 MB space) / Status S6.
36 A18/S5 Address Bus Output TTL Multiplexed Address bit 18 / Interrupt Enable Status S5.
37 A17/S4 Address Bus Output TTL Multiplexed Address bit 17 / Segment Status S4.
38 A16/S3 Address Bus Output TTL Multiplexed Address bit 16 / Segment Status S3.
39 A15 Address Bus Output TTL Address bit 15.
40 VCC Power Power +5.0 V +5 V power supply.

Common uses and repair diagnostics

The Intel 8088 (and its drop-in CMOS superset, the NEC V20 uPD70108) combines the 16-bit internal 8086 register architecture with an 8-bit multiplexed external address/data bus (AD0-AD7) and 20-bit physical addressing (1 MB space, A0-A19). In the Commodore PC-1, PC-10, PC-20, and Colt, Pin 33 (MN//MX) is strapped LOW (Maximum Mode) so an external 8288 bus controller (or Faraday FE2010/FE2010A chipset) decodes /S0-/S2 status lines into memory and I/O read/write strobes.

Fitted in the Commodore PC-1, PC-10 (I, II, III), PC-20 (I, II, III), and Commodore Colt. Note that for 7.16 MHz and 9.54 MHz Turbo operation on PC-10-III/PC-20-III/Colt boards, you must use an 8088-1 (10 MHz rated) or a 10 MHz NEC V20 (uPD70108C-10) — a standard 5 MHz D8088 will crash when switched out of 4.77 MHz mode.

  • Remember that 8088 Pin 21 (RESET) is ACTIVE-HIGH! If Pin 21 is stuck at +5V, check P8 Pin 1 (POWER GOOD) from the power supply.
  • Probe Pin 19 (CLK) for a clean 4.77 MHz (or 7.16/9.54 MHz) 33%-duty-cycle clock from the 8284A or Faraday FE2010A.
  • Probe Pin 22 (READY): if held LOW, the 8088 waits indefinitely — remove all ISA cards to rule out a hung IOCHRDY line.

Datasheets and references

Related chips

Theme Palette

Default Dark
High-contrast dark
Amber Terminal
Monochrome amber
Matrix CRT
Phosphor green
Workbench Light
Clean light mode

Audio & Display

Relay Click Sounds Web Audio API — soft mechanical clicks
CRT Scanline & Flicker Pure CSS overlay effect

System Info

Customization Panel Theme preference, audio FX, and CRT overlay settings are saved to your browser's localStorage and persist between visits. No cookies or server-side storage is used.
Keyboard Shortcuts Press Esc to close this panel. Use the header moon/sun icon to cycle themes.