Multi-ROM Switchers & Softkicking

Physical 27C800 / 27C160 / 27C322 multi-ROM switchers, pull-up wiring & CIA/reset triggers vs. Relokick, SKick, BlizKick & PiStorm Emu68.

1. Physical Multi-ROM EPROM Switchers (27C800 / 27C160 / 27C322)

Switching between Kickstart 1.3, Kickstart 3.1/3.2, and DiagROM on a single socket without drilling the case.

27C800 Dual-ROM & 27C160 Quad-ROM Pull-Up Wiring

  • How Bank Switching Works: The Amiga's 512 KB ROM window addresses A1–A18 (256K words = 512 KB). Higher address lines on larger EPROMs select which 512 KB slot is active:
    • 27C800 (1 MB = 2×512KB): Pin 1 is A18 (word address). Low (GND) = Bank 0 (e.g. KS 1.3); High (+5V) = Bank 1 (e.g. KS 3.1/3.2).
    • 27C160 (2 MB = 4×512KB): Pin 1 is A18 and Pin 42 is A19 (gives 4 banks: 00, 01, 10, 11).
  • 4.7k–10kΩ Pull-Up Resistor Rule: Never leave CMOS EPROM address pins floating, and never switch an address pin directly to the +5 V rail without a current-limiting resistor! Solder a 10 kΩ pull-up resistor from each bank pin (Pin 1 / Pin 42) to VCC (+5 V, Pin 22) so the pin defaults to HIGH (`1`), then wire your SPDT switch or jumper to pull the pin to GND (Pin 12 or 32) for LOW (`0`).

Reset-Hold ("No-Drill") Switchers & Gary/CIA Triggers

  • Keyboard Reset Monitoring (/KBRESET / /RESET): Modern PIC/ATtiny/CPLD no-drill switchers clip a single sense lead onto Gary Pin 5 (/KRES) on A500/A2000, Gayle Pin 63 (/KBRESET) on A600/A1200, or Odd/Even CIA Pin 34 (/RES).
  • Long-Reset Cycling: Holding Ctrl + Left Amiga + Right Amiga for >3 seconds clocks a flip-flop/counter on the switcher board, stepping A18/A19 to the next Kickstart bank and pulsing the power LED or piezo buzzer to confirm the selected ROM.
  • Dual-Socket A1200/A4000 Note: On 32-bit Amigas, the bank-select wire must tie A18/A19 of both U6A (HI) and U6B (LO) together in parallel so both chips switch banks in lockstep.

2. Softkicking & MapROM (Relokick, SKick, BlizKick & PiStorm Emu68)

Loading Kickstart ROMs into Fast RAM — zero EPROM burning and up to 5× faster OS execution.

Relokick 1.4a & SKick (Software Relocation)

  • Relokick 1.3 / 1.4a: Bootable floppy utility for A500+, A600, and A1200 that loads a 256 KB Kickstart 1.3 image into RAM at $200000 (or upper Chip RAM on 2 MB machines) and warm-reboots into KS 1.3 for legacy floppy games that crash on KS 2.0/3.x.
  • SKick (Sinz Kickstart Loader v3.46): Workbench/CLI softkicker that uses .RTB (Relocation Table) and .PAT files in DEVS:Kickstarts/ to relocate any Kickstart image into Fast RAM — the exact same `.RTB` format later adopted by WHDLoad!

BlizKick, ACAtune & PiStorm Emu68 MapROM

  • BlizKick (Phase5 Blizzard / CyberStorm / MMU 030-060): Uses the accelerator's hardware MapROM jumper (or MMU translation tables) to shadow a 512 KB Kickstart image into 60 ns 32-bit Fast RAM and patch modules on the fly (e.g. injecting ehide.device, scsi.device v46, NoClick, and SpeedyIDE) with a single cold reboot.
  • Individual Computers ACAtune: Run ACAtune -maprom * (copies physical ROM to Fast RAM) or ACAtune -maprom DEVS:kick31.rom at the top of S:Startup-Sequence.
  • PiStorm / PiStorm32-Lite (Emu68 config.txt): Emu68 maps any raw 256 KB/512 KB/1 MB `.rom` file directly from the FAT32 microSD card into ARM DDR RAM before the 68k JIT even starts! Simply copy your ROM to the FAT32 partition and add initramfs kick.rom (and optionally initramfs ext.rom for 1 MB custom ROMs) to config.txt.

Theme Palette

Default Dark
High-contrast dark
Amber Terminal
Monochrome amber
Matrix CRT
Phosphor green
Workbench Light
Clean light mode

Audio & Display

Relay Click Sounds Web Audio API — soft mechanical clicks
CRT Scanline & Flicker Pure CSS overlay effect

System Info

Customization Panel Theme preference, audio FX, and CRT overlay settings are saved to your browser's localStorage and persist between visits. No cookies or server-side storage is used.
Keyboard Shortcuts Press Esc to close this panel. Use the header moon/sun icon to cycle themes.