EPROM Burning & Pinout Guide

16-bit vs 32-bit HI/LO ROM sockets, A500 Rev 3/5 pin 1/31 mod, 27C400/27C800/27C160/27C322 adapters, and TL866II / T48 byte-swapping.

1. 16-Bit Single Socket vs. 32-Bit Dual HI/LO ROM Architecture

Why Commodore mask ROMs use JEDEC "mask-ROM" pinouts (27C400/27C800) rather than standard 27C040 8-bit EPROMs.

16-Bit Single ROM (A500 / A500+ / A600 / A2000)

  • One 16-Bit Wide Chip (U6): Supplies all 16 data bits (D0–D15) to the 68000 bus in a single cycle.
  • 40-Pin vs 42-Pin Motherboard Socket: A500 Rev 6A/8A and A600 have a 42-pin socket (designed for future 1 MB 27C800 ROMs). When plugging a 40-pin 27C400 into a 42-pin Amiga socket, align the chip with the bottom of the socket (Pin 21/22) — leaving Socket Pin 1 and Pin 42 empty!
  • CRITICAL — A500 Rev 3 & Rev 5 Socket Trap: Early A500 Rev 3 and Rev 5 boards wired Socket Pin 1 to +5 V and left Pin 31 floating. Plugging a 27C400 (or 512 KB Kickstart 2.04/3.1 mask ROM) straight into a Rev 3/5 socket shorts A17 or /BYTE-VPP and causes a Red/Black screen or overheats the EPROM! You must bend out EPROM Pin 1, jumper EPROM Pin 1 (A17) to Socket Pin 31, and tie EPROM Pin 31 (/BYTE) to Pin 21 (+5V VCC) (or use a Rev 5 ROM adapter socket).

32-Bit Dual HI/LO Split ROMs (A1200 / A3000 / A4000)

  • Two 16-Bit Chips in Parallel = 32-Bit Bus: To feed the 68EC020 / 68030 / 68040 32-bit data bus (`D0–D31`) in a single fetch, the 512 KB Kickstart is split across two 256 KB (or doubled 512 KB 27C400) chips.
  • HI ROM (Even 16-bit words, D16–D31): U6A on A1200 (Part 391773-01), U181 on A3000, U176 on A4000.
  • LO ROM (Odd 16-bit words, D0–D15): U6B on A1200 (Part 391774-01), U180 on A3000, U175 on A4000.
  • Word-Interleave Rule: Unlike 8-bit odd/even byte splitting on PCs/Atari STs, Amiga 32-bit ROMs split by 16-bit words (2 bytes at a time): Bytes `0,1` → HI, Bytes `2,3` → LO, Bytes `4,5` → HI, Bytes `6,7` → LO.

2. Supported EPROM Chips & Adapter Pinouts (27C400 / 27C800 / 27C160 / 27C322)

EPROM TypePackageCapacity (16-Bit)Kickstart Images HeldAmiga Socket CompatibilityProgrammer Adapter Needed
27C400 (M27C400 / AM27C400)DIP-40512 KB (256K×16)1× 512KB (or 2× 256KB)Direct drop-in (Pins 1 & 42 empty in 42-pin sockets; Rev 5 needs adapter)16-bit 27C400/800/160 ZIF adapter
27C800 (M27C800)DIP-421 MB (512K×16)2× 512KB (Dual Kickstart)Direct fit in 42-pin sockets; lift Pin 1 (A18) to switch ROMs via 10kΩ pull-up16-bit 27C400/800/160 ZIF adapter
27C160 (M27C160)DIP-422 MB (1M×16)4× 512KB (Quad Kickstart)Pin 42 is A19 (not VCC!); lift Pins 1 (A18) & 42 (A19) with 10kΩ pull-ups16-bit 27C400/800/160 ZIF adapter
27C322 (M27C322)DIP-424 MB (2M×16)8× 512KB (Octa Kickstart)16-bit ONLY (no /BYTE pin — Pin 13 is A20, Pin 31 is D15). Requires a 27C322-to-27C400 PCB adapter with 74LVC245 / address routing!27C322 bank-switching programmer adapter

3. Step-by-Step Burning & Byte-Swapping Workflow (TL866II Plus / XGecu T48)

Why your newly burned EPROM gives a black/red screen if you forget the 16-bit byte-swap.

Why Byte-Swapping is Mandatory

  • The Motorola 68000 is Big-Endian: at address $F80000, the high byte of the first word ($1114 for 512KB ROM, or $1111 for 256KB ROM) sits on D8–D15 and the low byte sits on D0–D7.
  • Standard PC EPROM programmers (TL866II Plus, XGecu T48/T56) load 16-bit buffers in Little-Endian order (Byte 0 → D0–D7, Byte 1 → D8–D15).
  • Quick Check in XGpro / Minipro Buffer: Look at offsets 000000–000003:
    • If it reads 11 14 4E F9 (or 11 11 4E F9) → Big-Endian (emulator order): Click Edit → Swap Byte so it becomes 14 11 F9 4E before burning!
    • If it already reads 14 11 F9 4E → Already byte-swapped (e.g. Hyperion's .bin programmer files) — burn as-is!

CLI / Python One-Liners for ROM Prep

  • 1. Double 256KB KS 1.3 to 512KB (for 27C400):
    copy /b kick13.rom + kick13.rom kick13_512.rom
  • 2. Byte-Swap a 512KB Image (Python):
    python -c "b=bytearray(open('in.rom','rb').read());b[0::2],b[1::2]=b[1::2],b[0::2];open('out_swapped.bin','wb').write(b)"
  • 3. Split 32-Bit AGA 512KB ROM into 2×256KB HI (U6A) & LO (U6B):
    python -c "b=open('ks31_a1200.rom','rb').read();hi=b''.join(b[i:i+2] for i in range(0,len(b),4));lo=b''.join(b[i+2:i+4] for i in range(0,len(b),4));open('U6A_HI_512.rom','wb').write(hi*2);open('U6B_LO_512.rom','wb').write(lo*2)" (then byte-swap both before burning to 27C400!).

Theme Palette

Default Dark
High-contrast dark
Amber Terminal
Monochrome amber
Matrix CRT
Phosphor green
Workbench Light
Clean light mode

Audio & Display

Relay Click Sounds Web Audio API — soft mechanical clicks
CRT Scanline & Flicker Pure CSS overlay effect

System Info

Customization Panel Theme preference, audio FX, and CRT overlay settings are saved to your browser's localStorage and persist between visits. No cookies or server-side storage is used.
Keyboard Shortcuts Press Esc to close this panel. Use the header moon/sun icon to cycle themes.