DiagROM & Amiga Test Kit Guide

Using DiagROM in the Kickstart socket for dead-board serial diagnostics (9600 8N1) and Amiga Test Kit (ATK) for subsystem verification.

1. DiagROM — Socket Installation & 9600-Baud RS-232 Serial Output

Why DiagROM boots even when Chip RAM, CIAs, or Denise/Lisa video are completely dead.

How DiagROM Works Without Working RAM

  • Standard Commodore Kickstart ROMs require working lower Chip RAM just to set up the 68000 supervisor stack and exception vectors — if Chip RAM Bit 0 is stuck, Kickstart halts on a Green Screen with zero details.
  • John "Chucky" Hertell's DiagROM keeps its state entirely inside the 680x0 CPU registers (D0–D7 / A0–A6) during initial POST, immediately bit-banging status characters out of Paula's UART (SERDAT $DFF030) while flashing raster bars on COLOR00 ($DFF180).
  • EPROM Files in the DiagROM Archive:
    • 16bit.bin → Pre-byteswapped 512 KB image ready to burn straight to a single 27C400 for A500 / A500+ / A600 / A2000 (remember the Rev 3/5 Pin 1/31 adapter!).
    • 32bitHI.bin & 32bitLO.bin → Pre-byteswapped 512 KB pair for A1200 (U6A=HI, U6B=LO), A3000 (U181/U180), and A4000 (U176/U175).

Serial Terminal Configuration & Bit-Fault Decoding

  • Serial Port Settings: Connect a DB25 Female Null-Modem cable to the Amiga's 25-pin RS-232 port (Pin 2 = TXD, Pin 3 = RXD, Pin 7 = GND) and set your PC terminal (PuTTY / minicom) to 9600 baud, 8 data bits, No parity, 1 stop bit (8N1), Flow Control = XON/XOFF or None.
  • Controlling DiagROM Remotely: If the Amiga keyboard or mouse is dead, you can navigate every DiagROM menu directly from your PC keyboard over the serial terminal!
  • Decoding Chip RAM Bit Errors: When DiagROM tests Chip RAM, it prints a 16-bit (or 32-bit on AGA) binary mask of working (`1`) vs stuck/floating (`0`) data bits. For example, on an A500 Rev 6A (four 44256 256K×4 DRAMs: U16–U19):
    • Bits D0–D3 bad → U16
    • Bits D4–D7 bad → U17
    • Bits D8–D11 bad → U18
    • Bits D12–D15 bad → U19

2. Amiga Test Kit (ATK / Systest) — Post-Boot Subsystem Verification

Keir Fraser's open-source diagnostic tool — available as a bootable ADF/Gotek image or burnable Kickstart ROM.

DiagROM vs. Amiga Test Kit: When to Use Which

  • Use DiagROM in the ROM socket when: The board shows a black, red, green, or yellow screen, will not boot from floppy/Gotek, or has suspected dead Chip RAM / address lines / Gary / Agnus faults.
  • Use Amiga Test Kit (ATK) when: The board boots (or has at least 256 KB working RAM for the ROM version of ATK) and you need precision testing of floppy head radial/azimuth alignment, 8520 CIA timers (TOD vs E-clock), Paula 4-channel audio sine sweeps, keyboard matrix rollover, and gameport/mouse quadrature counters.

Burning Amiga Test Kit Directly to an EPROM

  • Every Amiga Test Kit release includes a .rom build alongside the .adf floppy image!
  • Ultimate Dual-Diagnostic 27C800 EPROM: Concatenate DiagROM (512 KB) in Bank 0 and Amiga Test Kit ROM (doubled to 512 KB) in Bank 1 on a single 27C800 with a Pin 1 (`A18`) toggle switch — use Bank 0 to bring a dead motherboard back to life, then flip to Bank 1 to soak-test RAM, CIAs, audio, and drives!

Need interactive fault-isolation trees for boot colours or CIA pins? Open the Amiga Diagnostics & CIA Isolation Guide →

Theme Palette

Default Dark
High-contrast dark
Amber Terminal
Monochrome amber
Matrix CRT
Phosphor green
Workbench Light
Clean light mode

Audio & Display

Relay Click Sounds Web Audio API — soft mechanical clicks
CRT Scanline & Flicker Pure CSS overlay effect

System Info

Customization Panel Theme preference, audio FX, and CRT overlay settings are saved to your browser's localStorage and persist between visits. No cookies or server-side storage is used.
Keyboard Shortcuts Press Esc to close this panel. Use the header moon/sun icon to cycle themes.