CSG 8374 Alice Pinout — Amiga 1200/4000 AGA DMA, Blitter & Chip RAM Controller (PLCC-84)

PLCC-84 · Sound & Video · CSG 8374 Alice (391010-01) — PLCC-84

CSG 8374 Alice (AGA DMA Controller) (PLCC-84) — Printable IC Pinout & Signal SheetHigh-contrast DIP/PLCC pinout diagram, supply pin highlights (+5V/GND/+12V), and full 84-pin table.

Pinout diagram

Used in Retro Machine Hubs

Click any system badge below to jump directly to its dedicated repair, schematic, and diagnostic Machine Hub:

Summary specifications

Technology HMOS-2 gate array
Operating Voltage +5 V (VCC1 pin 15, VCC2 pin 52; GND1 pin 82, GND2 pin 42, GND3 pin 58)
Clocks SCLK + 14 MHz inputs (pins 34/36) sourced from Lisa; 7 MHz out pin 38
Chip RAM 2 MB via DRA0-DRA9, 32-bit data bus, Fast Page Mode
PAL/NTSC /NTSC pin 41 selects video standard on AGA machines
Note Alice is NOT compatible with 8370/8372/8375 sockets — AGA machines only.

Full pin reference

Pin Name Group Direction Levels Description Expected Signal
1 DRD13 Data Bus Bidirectional TTL Chip RAM data bit 13.
2 DRD12 Data Bus Bidirectional TTL Chip RAM data bit 12.
3 DRD11 Data Bus Bidirectional TTL Chip RAM data bit 11.
4 DRD10 Data Bus Bidirectional TTL Chip RAM data bit 10.
5 DRD9 Data Bus Bidirectional TTL Chip RAM data bit 9.
6 DRD8 Data Bus Bidirectional TTL Chip RAM data bit 8.
7 DRD7 Data Bus Bidirectional TTL Chip RAM data bit 7.
8 DRD6 Data Bus Bidirectional TTL Chip RAM data bit 6.
9 DRD5 Data Bus Bidirectional TTL Chip RAM data bit 5.
10 DRD4 Data Bus Bidirectional TTL Chip RAM data bit 4.
11 DRD3 Data Bus Bidirectional TTL Chip RAM data bit 3.
12 DRD2 Data Bus Bidirectional TTL Chip RAM data bit 2.
13 DRD1 Data Bus Bidirectional TTL Chip RAM data bit 1.
14 DRD0 Data Bus Bidirectional TTL Chip RAM data bit 0 (LSB).
15 VCC1 Power Power +5 V +5 V supply.
16 /RESET Control Input TTL, active low System reset input.
17 /INTR Control Output TTL, active low Interrupt request to CPU (from Paula/Agnus priority encoder).
18 DMAL Control Input TTL Serial DMA-request stream from Paula — audio, disk and sprite slot requests.
19 /BLS Control Input TTL, active low Blitter slowdown from Gayle/address decode — yields Chip RAM to CPU.
20 /DBR Control Input TTL, active low DMA bus request/blitter-active flag.
21 /WE Control Output TTL, active low Chip RAM write enable.
22 R/W Control Input TTL Processor read/write direction.
23 /REGEN Control Input TTL, active low Register enable — CPU is addressing $DFFxxx custom registers.
24 NC2 No Connect Not connected - No connect (was /AS on Agnus).
25 /RAMEN Control Input TTL, active low Chip RAM enable from address decoder.
26 RGA8 Address Bus Output TTL Register address bus bit 8 to Lisa and Paula.
27 RGA7 Address Bus Output TTL Register address bus bit 7.
28 RGA6 Address Bus Output TTL Register address bus bit 6.
29 RGA5 Address Bus Output TTL Register address bus bit 5.
30 RGA4 Address Bus Output TTL Register address bus bit 4.
31 RGA3 Address Bus Output TTL Register address bus bit 3.
32 RGA2 Address Bus Output TTL Register address bus bit 2.
33 RGA1 Address Bus Output TTL Register address bus bit 1 (LSB).
34 SCLK Clock / Timing Input TTL SCLK clock input from Lisa — synchronises Alice's clock generator.
35 A20 Address Bus Input TTL CPU address bit 20.
36 14MHz Clock / Timing Input TTL 14 MHz 14 MHz clock input from Lisa (was /XCLKEN on Agnus).
37 /CDAC Clock / Timing Output TTL 7 MHz 7 MHz quadrature clock output.
38 7MHz Clock / Timing Output TTL 7.09 MHz Master 7 MHz system clock output.
39 CCKQ Clock / Timing Output TTL 3.55 MHz Colour clock quadrature to Lisa and Paula.
40 CCK Clock / Timing Output TTL 3.55 MHz Master colour clock to Lisa, Paula and Gayle.
41 /NTSC Control Input TTL Video standard select — low = PAL 50 Hz, high = NTSC 60 Hz.
42 GND2 Ground Power 0 V Ground.
43 DRA0 Address Bus Output TTL Multiplexed Chip RAM address bit 0 (A1200 -02 Budgie boards need the 470R pull-up here).
44 DRA1 Address Bus Output TTL Chip RAM address bit 1.
45 DRA2 Address Bus Output TTL Chip RAM address bit 2.
46 DRA3 Address Bus Output TTL Chip RAM address bit 3.
47 DRA4 Address Bus Output TTL Chip RAM address bit 4.
48 DRA5 Address Bus Output TTL Chip RAM address bit 5.
49 DRA6 Address Bus Output TTL Chip RAM address bit 6.
50 DRA7 Address Bus Output TTL Chip RAM address bit 7.
51 DRA8 Address Bus Output TTL Chip RAM address bit 8.
52 VCC2 Power Power +5 V +5 V supply.
53 NC1 No Connect Not connected - No connect (was /CASL on Agnus).
54 /CAS Control Output TTL, active low Chip RAM column address strobe (unified on AGA).
55 Vbb Power Power -5 V substrate Substrate bias — tied to board's negative generator.
56 DRA9 Address Bus Output TTL Chip RAM address bit 9 — needed for 2 MB Chip RAM.
57 /RAS Control Output TTL, active low Chip RAM row address strobe.
58 GND3 Ground Power 0 V Ground.
59 A19 Address Bus Input TTL CPU address bit 19.
60 A1 Address Bus Input TTL CPU address bit 1.
61 A2 Address Bus Input TTL CPU address bit 2.
62 A3 Address Bus Input TTL CPU address bit 3.
63 A4 Address Bus Input TTL CPU address bit 4.
64 A5 Address Bus Input TTL CPU address bit 5.
65 A6 Address Bus Input TTL CPU address bit 6.
66 A7 Address Bus Input TTL CPU address bit 7.
67 A8 Address Bus Input TTL CPU address bit 8.
68 A9 Address Bus Input TTL CPU address bit 9.
69 A10 Address Bus Input TTL CPU address bit 10.
70 A11 Address Bus Input TTL CPU address bit 11.
71 A12 Address Bus Input TTL CPU address bit 12.
72 A13 Address Bus Input TTL CPU address bit 13.
73 A14 Address Bus Input TTL CPU address bit 14.
74 A15 Address Bus Input TTL CPU address bit 15.
75 A16 Address Bus Input TTL CPU address bit 16.
76 A17 Address Bus Input TTL CPU address bit 17.
77 A18 Address Bus Input TTL CPU address bit 18.
78 /LPEN I/O Input TTL, active low Light pen trigger from controller port.
79 /VSYNC I/O Bidirectional TTL, active low Vertical sync — also feeds CIA-A TOD tick.
80 /CSYNC I/O Bidirectional TTL, active low Composite sync to DB23 video port.
81 /HSYNC I/O Bidirectional TTL, active low Horizontal sync (~15.6-31 kHz on AGA scan modes).
82 GND1 Ground Power 0 V Ground.
83 DRD15 Data Bus Bidirectional TTL Chip RAM data bit 15 (MSB of low word; D16-D31 handled via Lisa wide bus).
84 DRD14 Data Bus Bidirectional TTL Chip RAM data bit 14.

Common uses and repair diagnostics

Alice (CSG 8374, part 391010-01) is the AGA evolution of the 8375 Fatter Agnus — same PLCC-84 package, same 25-channel DMA/blitter/copper engine, but re-spun for the 68020/68030/68040 buses and a 32-bit Chip RAM interface with Fast Page Mode. Fitted at U2 on the A1200, U211 on the A4000, and U2 on the CD32. Alice cannot be retrofitted into OCS/ECS machines.

U2 on the Amiga 1200, U211 on the A4000 (U200 on A4000T), U2 on the CD32. On an A1200 that boots to a green screen, suspect the Chip RAM bank, Alice's /RAS//CAS outputs, or electrolyte-corroded DRA0-DRA9 vias before the chip itself.

  • Alice is soldered, not socketed — condemn it only after checking the 28/14 MHz clocks on pins 34/36, which come FROM Lisa; a dead Lisa starves Alice of clocks.
  • Green boot screen on A1200: check DRA0-DRA9 (pins 43-51, 56) continuity to the Chip RAM SIMM pads and the DRA0 470R pull-up required on -02 Budgie boards.
  • /NTSC pin 41 stuck high on a PAL board gives 60 Hz output some SCART TVs reject — verify the pin's solder joint to the PAL/NTSC jumper pad.
  • Pin 55 (Vbb) needs the -5 V substrate bias from the onboard charge pump; a corroded supply trace causes erratic DMA failures.

Datasheets and references

Related chips

Theme Palette

Default Dark
High-contrast dark
Amber Terminal
Monochrome amber
Matrix CRT
Phosphor green
Workbench Light
Clean light mode

Audio & Display

Relay Click Sounds Web Audio API — soft mechanical clicks
CRT Scanline & Flicker Pure CSS overlay effect

System Info

Customization Panel Theme preference, audio FX, and CRT overlay settings are saved to your browser's localStorage and persist between visits. No cookies or server-side storage is used.
Keyboard Shortcuts Press Esc to close this panel. Use the header moon/sun icon to cycle themes.