Commodore PC Compatible Hub (PC-1 to PC-60 & Colt)
Bench reference for Commodore's XT & 286/386 AT compatibles — SW201 video DIP switches, JMP208 XTA jumpers, G=FA00:5 low-level formatting, XT-IDE CF upgrades, P8/P9 PSUs, and Varta 8042 trace repair.
VARTA Barrel Battery Corrosion & P8/P9 XT/AT Power Supply Alert
Commodore PC-10-III, PC-20-III, Colt, and all 286/386 AT-class boards (PC-30, PC-40, PC-50, PC-60) shipped with a soldered 3.6 V VARTA NiCd barrel battery right beside the 5-pin DIN keyboard jack, the 8042 keyboard microcontroller (on AT boards), and the Ricoh RP5C15 / OKI M6242B RTC. Alkaline potassium hydroxide creeps along the copper traces and severing the keyboard clock/data lines and BIOS ROM chip-selects — snip the Varta off immediately before powering on!
1 VARTA Trace Repair Map (8042 KBC & RTC)
- Neutralise & Strip: Cut the 3-pin Varta cell off flush, flood blue/green crust with white vinegar (acetic acid) for 2 minutes, scrub with IPA, and fiberglass-pen darkened solder mask down to bare copper.
- PC-10-III / Colt RTC Zone: Check the 32.768 kHz crystal (`Y201`), diode `D201`/`D202`, and address lines `A0–A3` feeding the **OKI M6242B / Ricoh RP5C15** real-time clock.
- PC-30 / PC-40 / PC-60 (286/386) 8042 Keyboard Error: When the board halts with
Keyboard Error or No Keyboard Present, check continuity from the 5-pin DIN socket:- DIN Pin 1 (`KB_CLK`) → Inductor/ferrite → 8042 Pin 1 (`T0` / `P26`) & pull-up resistor pack.
- DIN Pin 2 (`KB_DATA`) → Inductor/ferrite → 8042 Pin 39 (`T1` / `P27`).
- 8042 Pin 20 (`GND`), Pin 40 (`+5V`), and Pin 2/3 (`XTAL1`/`XTAL2`) + adjacent `74LS06` / `74F07` open-collector buffer!
2 Standard P8 / P9 XT & AT PSU Pinout
Rule #1 when plugging P8 & P9 Molex connectors onto the motherboard: "Black-to-Black in the Middle" (P8 Pins 5–6 and P9 Pins 1–2 must meet at the center!):
| Connector / Pin | Wire Colour | Rail & Tolerance | Bench Notes |
|---|---|---|---|
| P8 Pin 1 | Orange | POWER GOOD (+5V) | Must rise to +5V 100–500 ms after rails stabilize (holds CPU in RESET if low!) |
| P8 Pin 2 | Red (AT) / NC (XT) | +5.0V DC | 4.85–5.15 V logic rail |
| P8 Pin 3 | Yellow | +12.0V DC | 11.5–12.6 V FDD/HDD spindle motors & ISA |
| P8 Pin 4 | Blue | -12.0V DC | RS-232 serial negative rail |
| P8 Pins 5 & 6 | Black | GND (0V) | Centre-facing ground pins! |
| P9 Pins 1 & 2 | Black | GND (0V) | Centre-facing ground pins! |
| P9 Pin 3 | White | -5.0V DC | ISA Pin B5 (early DRAM / sound cards) |
| P9 Pins 4, 5, 6 | Red | +5.0V DC | Main motherboard logic supply (15–20 A) |
3 AT/ATX Conversion & Tantalum Short Checks
- ATX-to-AT P8/P9 Adapter Warning: Modern ATX supplies often omit the −5 V rail (P9 Pin 3). While 8088/286/386 motherboards using 41256/SIMM RAM only route −5 V to ISA Slot Pin B5, early ISA cards require an ATX-to-AT adapter with an onboard 7905 (−5 V) regulator.
- Shorted 3-Leg Teardrop Tantalum Caps: If the PSU fan twitches once and shuts down, check the orange/yellow radial tantalum decoupling capacitors (`10 μF 16V`) along the ISA slots across the +12 V and −12 V rails!
Commodore PC Model Variations & Architectural Matrix
Select your Commodore PC generation to inspect CPU speeds, turbo keyboard hotkeys, chipset ICs, onboard video, and storage interfaces.
Commodore PC-1 (1987) — Ultra-Compact Pizza-Box Wedge XT
CPU: Siemens 8088 @ 4.77 MHz • Chipset: Faraday FE2010 • Video: Paradise PVC2/PVC4 (CGA/Hercules)Architecture & Onboard Video
Styled to match the Amiga 500/1000 aesthetic, the Commodore PC-1 packs a full IBM PC/XT compatible onto a tiny single-drive pizza-box board using the Faraday FE2010 single-chip XT system controller, 512 KB RAM (expandable to 640 KB onboard with four `41464` + four `4164` DRAMs), and built-in CGA / Hercules Monochrome / Plantronics 16-colour video on both a DB9 TTL RGBI/MDA port and an RCA composite jack.
ISA Expansion Box & External Drive Bus
The base PC-1 has no internal ISA slots; instead, a rear 62-pin proprietary bus header connects to the optional sidecar ISA Expansion Unit (adding two 8-bit ISA slots for an XT-IDE or sound card). The rear DB23/DIN external floppy port uses Commodore's custom external 5.25″/3.5″ drive pinout (distinct from Amiga DB23!).
| Model Series | CPU & Clock Speeds | Turbo Hotkeys / Switch | Core Chipset & Video | RAM & Storage Interface |
|---|---|---|---|---|
| PC-1 (1987) | Siemens 8088 @ 4.77 MHz | Fixed 4.77 MHz | Faraday FE2010 + Paradise PVC2/PVC4 (CGA / Hercules / Plantronics) |
512 KB → 640 KB (`41464`); 1× 5.25″ 360KB FDD; External 8-bit ISA sidecar |
| PC-10-I / II & PC-20-I / II (1984–86) | Intel 8088 @ 4.77 MHz | Fixed 4.77 MHz | Discrete 8284/8288/8237/8259/8253/8255 XT logic + full-length ISA video card | 256 KB → 640 KB (`4164`/`41256`); 5–8× 8-bit ISA slots; MFM HDD (`WD1002-WX2`) |
| PC-10-III / PC-20-III / Colt (1987–89) | Siemens 8088-1 or NEC V20 @ 4.77 / 7.16 / 9.54 MHz | CTRL+ALT+S (4.77MHz) CTRL+ALT+T (7.16MHz) CTRL+ALT+D (9.54MHz) |
Faraday FE2010A + Onboard ATI CW16800 / Paradise PVC4 (MDA/Hercules/CGA/Plantronics via SW201) |
640 KB onboard; 3× 8-bit ISA; Onboard 360K/720K FDD + 40-pin 8-Bit XTA (`JMP208`) + RTC |
| PC-30-III / PC-40-III (AT 286) (1988–90) | Intel/AMD 80286 @ 10 / 12 / 16 MHz (Socketed 80287) | CTRL+ALT+- / + or front Turbo switch | acer / Chips & Tech NEAT 286 chipset; 8042 KBC; VGA/EGA ISA card (or onboard VGA on III) | 1 MB → 4/16 MB DIP/SIMM; 16-bit ISA slots; 1.2MB / 1.44MB FDD + 16-bit AT IDE / MFM; Varta or Dallas RTC |
| PC-50-II / PC-60-III (386SX / 386DX) (1989–91) | Intel 80386SX-16/20 or 80386DX-25 (Floor Tower on PC-60) | Front Turbo button / BIOS setup | Intel / C&T 386 chipset + 64 KB SRAM cache (PC-60); 8042 KBC | 2 MB → 16 MB 30-pin SIMMs; 6–8× 16-bit ISA; AT IDE + dual FDD; Varta or Dallas DS1287 RTC |
| SL / SD Slimline (SD286 / SL286 / SL386SX) | 80286-12/16 or 80386SX-16/20/25 | BIOS / Keyboard hotkey | Onboard Paradise PVGA1A / WD90C00 16-bit VGA (DB15) | 1–4 MB SIMM/SIPP; Horizontal ISA riser card; 16-bit AT IDE + 3.5″ 1.44MB FDD |
Motherboard DIP Switches (SW201) & JMP208 XTA Jumper Reference
Configure onboard MDA/Hercules/CGA video modes or disable onboard video & XTA to install a 16-bit ISA VGA card and XT-IDE CF controller.
PC-10-III / PC-20-III / Colt 8-Position DIP Switch Block (SW201)
Located near the rear keyboard/video connectors on the ASSY 312622 / 380222 motherboard. Configure switches with power OFF:
| Target Video / System Mode | SW 1 | SW 2 | SW 3 | SW 4 | Notes |
|---|---|---|---|---|---|
| Monochrome / Hercules (MDA 720×348 TTL) | OFF | OFF | ON | OFF |
18.432 kHz TTL on DB9; composite disabled |
| CGA 80×25 Colour (15.7 kHz RGBI + Composite) | OFF | ON | OFF | OFF |
Standard 80-column RGBI (DB9) & RCA composite |
| CGA 40×25 Colour (TV / Composite Mode) | ON | OFF | OFF | OFF |
40-column boot mode for composite monitors |
| External ISA EGA / VGA Card Bypass! | ON | ON | ON | ON |
Disables onboard ATI/Paradise video so an 8/16-bit ISA VGA card works without conflict! |
Switches 5–8 on SW201: SW5 = Monitor type/sync polarity; SW6 = 8087 FPU (`ON` = No 8087, `OFF` = 8087 installed); SW7 & SW8 = Number of Floppy Drives (`ON/ON` = 1 drive, `OFF/ON` = 2 drives).
JMP208 — Onboard 8-Bit XTA Hard Drive Enable / Disable Jumper
The PC-10-III, PC-20-III, and Colt include an onboard 40-pin 8-bit XTA (XT-Attachment) controller decoded at I/O port 320h–323h (IRQ 5, DMA 3) with a Western Digital option BIOS mapped inside the main ROM at FA00:0000:
| Jumper Header | Setting | Effect & When to Use |
|---|---|---|
JMP208 Pins 1–2 (or Closed) |
ENABLED (Factory PC-20-III) | Enables the onboard 40-pin XTA interface (`320h`, IRQ 5) and the `FA00:0000` WD XTA BIOS. Use ONLY when a working 8-bit XTA drive (`ST-351A/X`, `ST-325X`, `CP-2024XT`) is attached! |
JMP208 Pins 2–3 (or Open) |
DISABLED (Factory PC-10-III / Colt) | Mandatory when installing an XT-IDE CF card or removing a dead XTA drive! Leaving `JMP208` enabled without an XTA drive causes a 45-second POST hang and `1701 Hard Disk Controller Failure`! |
XTA Low-Level Format (DEBUG G=FA00:5) & Modern XT-IDE CF Upgrades
Formatting vintage 8-bit XTA hard drives (Seagate ST-351A/X, ST-325X, Conner CP-2024XT) and installing modern 8-bit XT-IDE CompactFlash cards.
1 Low-Level Formatting Internal XTA Drives (G=FA00:5)
When an original 20 MB / 40 MB 8-bit XTA drive loses sector headers over time (Sector Not Found / `1701`), invoke the routine built right into Commodore's BIOS ROM at segment FA00h:
- Set
JMP208to ENABLED (1–2) and connect your 40-pin XTA drive. - Boot from an MS-DOS 3.30 / 5.0 / 6.22 floppy disk containing
DEBUG.COM,FDISK.EXE, andFORMAT.COM. - At the
A:\>prompt, launch DEBUG and jump to the onboard WD XTA formatter:
A:\>DEBUG
-G=FA00:5(Note: On external WD1002A-WX1 ISA MFM/XTA cards, use-G=C800:5) - Follow the prompt: select Drive
0(or `C`), confirm interleave (default3or4), and enter the drive's cylinder/head parameters if prompted, then runFDISKandFORMAT C: /S.
| Compatible 8-Bit XTA Drive | Capacity & CHS Geometry | Critical Drive Jumper Notes |
|---|---|---|
| Seagate ST-351A/X (3.5″ 1″ low-profile) | 42.8 MB (820 Cyl, 6 Heads, 17 SPT) | Dual-mode AT/XT drive! Remove jumper J6 (Pins 9–10 = XT 8-Bit Mode) and jumper J6 Pins 1–2 (Master). Most reliable XTA drive ever made! |
| Seagate ST-325X (3.5″) | 21.4 MB (615 Cyl, 4 Heads, 17 SPT) | Dedicated 8-bit XTA interface; factory fitted in late PC-20-III systems. |
| Conner CP-2024XT / Miniscribe 8425XT | 20 MB (615 Cyl, 4 Heads, 17 SPT) | Check rubber head-stop bumper inside Conner drives (turns to sticky goo) and stepper grease on Miniscribe 8425XT. |
2 Modern Storage: 8-Bit XT-IDE ISA + CompactFlash Setup
The cleanest, silent solid-state upgrade for any PC-1 (with sidecar), PC-10, PC-20, Colt, or PC-30/40 is an 8-bit XT-IDE Rev 4 or Lo-tech ISA-CF card running XtideUniversalBios (`ide_xt.bin`):
- Step 1 — Disable Onboard XTA (`JMP208`): Move motherboard jumper
JMP208to DISABLED (2–3 / Open) so the motherboard's `FA00:0000` XTA BIOS does not stall POST looking for an XTA drive. - Step 2 — Set XT-IDE I/O & EEPROM Switches:
- I/O Base Address:
300h(default for `ide_xt.bin`; avoids `320h` XTA and `378h` LPT1). - Boot EEPROM Window:
C800horD000h(ensure no EMS or network ROM shares that 8 KB window) and setEEPROM ENABLE = ON.
- I/O Base Address:
- Step 3 — Initialize the CompactFlash MBR (`FDISK /MBR`): Brand-new industrial CF cards (64 MB–2 GB Cisco/Transcend/SanDisk) often have non-DOS boot code in Sector 0 that hangs After formatting. Boot MS-DOS 5.0/6.22 from floppy and run:
A:\>FDISK /MBR
A:\>FDISK(create Primary DOS Partition)
A:\>FORMAT C: /S - Bonus — NEC V20 (`uPD70108C-10`) CPU Upgrade: Replacing the 40-pin 8088 with a 10 MHz NEC V20 allows flashing the faster
ide_xtp.bin(XT+ 80186 instruction set) BIOS onto the XT-IDE card, nearly doubling CF transfer throughput!
Complete Diagnostic Flowchart: Commodore PC-1 / PC-10 / Colt & PC-30/40/60 (XT/286/386) Fault Isolation (Commodore PC Compatible Series (PC-1, PC-10/20-III, Colt, PC-30/40/50/60, SL/SD))
BIOS EPROM Splitting, Checksums & Dallas DS1287 RTC Rework
8-bit vs 16-bit HI/LO BIOS EPROM rules, the 0x00 modular checksum requirement, and 286/386 CMOS battery fixes.
8-Bit Single vs. 16-Bit Even/Odd (HI/LO) BIOS EPROMs
| System Family | EPROM Type & Sockets | Byte Splitting & Checksum Rule |
|---|---|---|
| PC-1 / PC-10-I/II | 1× 2764 (8 KB) or 27128 (16 KB) (DIP-28) | Single 8-bit linear ROM mapped ending at FFFF:000F. No byte splitting required. |
| PC-10-III / PC-20-III / Colt | 1× 27256 (32 KB) at U201 (DIP-28) |
32 KB 8-bit image (`F800:0000–FFFF:000F`): lower half contains the `FA00:0000` WD XTA option ROM, upper half contains the main Commodore System BIOS v4.36/4.41. |
| PC-30 / PC-40 / PC-50 / PC-60 (286/386 AT) | 2× 27128 (16 KB) or 2× 27256 (32 KB) (`EVEN/LO` & `ODD/HI`) | 8-Bit Interleaved Split: Even byte offsets (`0, 2, 4...` = `D0–D7`) go into the EVEN / LO EPROM; Odd byte offsets (`1, 3, 5...` = `D8–D15`) go into the ODD / HI EPROM. |
8-Bit Modular Checksum Rule (`ROM ERROR`): IBM XT/AT BIOS POST sums every byte in the BIOS segment modulo 256; the final byte of the ROM adjusts the total so the 8-bit sum equals `0x00`. Verify your dump or patched BIOS in Smiggy's .BIN / ROM Patcher & Checksum Tool before burning!
PC-30 / PC-40 / PC-60 Dallas DS1287 / External CMOS Battery Fix
- Boards with Soldered VARTA Barrel + Discrete MC146818 RTC: Remove the Varta barrel battery completely, clean corrosion around the `MC146818` / `8042`, and wire a 3×AA alkaline or `CR2032` + `1N4148` blocking diode pack to the 4-pin `EXT BATT` header (`Pin 1 = +6V`, `Pin 2 = Key`, `Pin 3 = NC`, `Pin 4 = GND`).
- Boards with Potted Dallas `DS1287` / `DS12887` Module: Late 286/386 revisions use a 24-pin potted Dallas RTC module with an internal lithium cell plotted in epoxy:
- Best Fix: Desolder the dead DS1287, install a 24-pin machined IC socket, and plug in a modern Necroware `NWX287` (with replaceable CR1220 coin cell holder) or a new-production `DS12887+`.
- Dremel Rework: Alternatively, mill into the side beneath the "DALLAS" logo to expose internal battery pins Pin 16 (`GND`) and Pin 20 (`+3V BATT`), sever the dead internal cell tab on Pin 20, and solder a CR2032 holder on top.
Key ICs, Connector Pinouts & Further Reading
Interactive chip pinouts and connector guides for Commodore PC compatibles.
Interactive IC Pinouts
- Intel / Siemens 8088 CPU (DIP-40) — PC-1, PC-10, PC-20 & Colt processor
- Intel 8255A PPI (DIP-40) — XT keyboard, speaker & DIP switch port
- 4164 (64K×1) DRAM (DIP-16) — PC-1 / PC-10 main & parity RAM
- 74LS245 Octal Bus Transceiver — ISA & local data bus buffering
Connector & Bench Tools
Schematics & Related Hubs
- Zimmers.net Commodore PC Schematics — PC-1, PC-10-III, PC-30 & PC-40 service manuals
- Commodore 64 Hub • C128 Hub • PET Hub • SX-64 Hub
- Amiga Hub • Big-Box Amiga Hub • Osborne 1 & Kaypro II Hub
- Apple IIe Hub • Atari ST Hub • TRS-80 Hub • MSX Hub
Commodore PC (PC-1 to PC-60 / Colt) — Capacitor & Recap Reference
Board revisions, electrolytic capacitor lists, voltage/farad ratings, and Through-Hole & Early SMD servicing notes.
Commodore PC (PC-1 to PC-60 / Colt) Capacitor & Power Stage Checklist
This system uses Through-Hole & Early SMD electrolytic capacitors. When servicing Commodore PC Compatible (PC-1 to PC-60 & Colt) on the bench, always use 105°C low-ESR radial or SMD electrolytic replacements (Nichicon PW/HE, Panasonic FR/FC, or Rubycon ZLH) and inspect the PCB for electrolyte corrosion around voltage regulators, audio coupling stages, and video DAC outputs.
- Voltage Rating Rule: Match the original capacitance (µF) exactly; you may safely step up the voltage rating one tier (e.g. 10V → 16V or 16V → 25V) where physical lead spacing and can height allow.
- Power Rail Verification: Before and after recapping, verify DC rail voltages and AC ripple (<50 mVpp) across the main CPU (
8088 / NEC V20 / 80286 / 80386 @ 4.77–25 MHz) and RAM (512 KB – 640 KB XT / 1 MB – 16 MB AT) supply pins.
Complete Diagnostic Flowchart: Commodore PC-1 / PC-10 / Colt & PC-30/40/60 (XT/286/386) Fault Isolation (Commodore PC Compatible Series (PC-1, PC-10/20-III, Colt, PC-30/40/50/60, SL/SD))
Commodore PC (PC-1 to PC-60 / Colt) — System Bench Tools & IC Pinouts
Click any chip below to open its interactive DIP/PLCC pinout diagram, pin-by-pin signal table, and oscilloscope test waveforms.
Intel 8253 PIT
Intel 8253 / 8253-5 / 8254 / D8253C / KR580VI53
Three 16-bit timers, six modes — and the three counters pins appear in three different orders, the signature trap.
Open Interactive Pinout →Intel 8255A PPI
Intel 8255A / D8255AC-2 / NEC D8255AC / KR580VV55A
Three 8-bit I/O ports in one 40-pin DIP — port C nibbles run in opposite directions and RESET is active high, the two signature traps.
Open Interactive Pinout →Intel 8088 / NEC V20 CPU
Intel 8088 / SAB8088-1 / NEC V20 uPD70108 (DIP-40)
16-bit x86 CPU with 8-bit external bus (AD0-AD7) powering the Commodore PC-1, PC-10, PC-20, Colt & IBM XT.
Open Interactive Pinout →Retro Emulator Hub (C64, C128, ZX & CPC)
Boot .D64, .D71, .PRG, .TAP, .TZX, .Z80, .SNA & .DSK images client-side with Warp Mode, Drive A/B & BASIC macros.
VisualizerSignal & Trace Visualizer (Scope)
Compare healthy vs. faulty CPU clocks, reset ramps, PLA strobes, and 5V PSU ripple waveforms.
Disassembler & ROM LabRetro File Utilities (Rust/Wasm)
6502/6510 disassembler with IC register links, C64 .D64 parser, and EPROM CRC32 verifier/patcher.
Memory & Address LabVisual Memory Mapper & Decoder
Interactive 64KB ($0000–$FFFF) memory map, PLA/ROM banking toggles, 16-bit Low/High split & Video RAM mapper.
Code & .PRG LabBASIC-to-Assembly & .PRG Tokenizer
Convert legacy BASIC into label-based code, 6502/Z80 POKE/PEEK opcodes, and downloadable .PRG binaries.
Instruction Set & TimingOpcode Lookup & Cycle Counter
Search 6502, Z80 & 68000 opcodes, inspect status flags, and calculate raster loop clock cycles.
Assembler & Disassembler6502 & Z80 Cross-Assembler (.PRG/.TAP)
Compile 6502/6510 & Z80 source into runnable .PRG and .TAP binaries or disassemble uploaded files.
Logic & PinoutsConnector & Port Pinout Reference
59 interactive RGB SCART, DIN A/V, PSU polarity, joystick, floppy, and expansion bus pinouts.
Logic & PinoutsLogic & RAM Substitution Guide
Cross-reference 4116→4164 DRAM mods, 2364→27C256 EPROM adapters, and 74LS/74HCT swaps.